Off-design operation of an 900 MW-class power plant with utilization of low temperature heat of flue gases
Abstract
This article presents the o-design operation of a 900 MW-class steam turbine cycle upgraded with utilization of lowtemperaturewaste heat taken from boiler flue gas. The low-temperature heat contributes to increasing the eciency ofpower plants without introducing many complex changes to the whole system. The base for investigations was a powerunit operating in o-design conditions and supplied with steam from a BB–2400 boiler. Modifications to the model weremade using commercially available software and by applying the Stodola equation and the SCC method. Calculationsfor o-design conditions show that, after making some modifications to the system, both heat and electricity generationcould be increased through the addition of a low-temperature heat exchanger.References
[1] M. Amirinejad, N. Tavajohi-Hasankiadeh, S.S. Madaeni, M.A. Navarra, E. Rafiee, B. Scrosati: “Adaptive neuro-fuzzy inference system and artificial neural network modeling of proton exchange membrane fuel cells based on nanocomposite and recast Nafion membranes”, International Journal of Energy Research, pp. 347-357, 2013.
[2] M. Amirinejad, N. Tavajohi-Hasankiadeh, S.S. Madaeni, M.A. Navarra, E. Rafiee, B. Scrosati: “Adaptive neuro-fuzzy inference system and artificial neural network modeling of proton exchange membrane fuel cells based on nanocomposite and recast Nafion membranes”, International Journal of Energy Research, pp. 347-357, 2013.
[3] D.P. Bakalis, A.G. Stamatis: “Incorporating available micro gas turbines and fuel cell: Matching considerations and performance evaluation”, Applied Energy, pp. 607-617, 2013.
[4] D.P. Bakalis, A.G. Stamatis: “Incorporating available micro gas turbines and fuel cell: Matching considerations and performance evaluation”, Applied Energy, pp. 607-617, 2013.
[5] T. Bartela, A. Skorek-Osikowska, J. Kotowicz: “Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation”, Energy, pp. 513-523, 2014.
[6] T. Bartela, A. Skorek-Osikowska, J. Kotowicz: “Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation”, Energy, pp. 513-523, 2014.
[7] W.M. Budzianowski: “Modelling of CO2 content in the atmosphere until 2300: Influence of energy intensity of gross domestic product and carbon intensity of energy”, International Journal of Global Warming, pp. 1-17, 2013.
[8] W.M. Budzianowski: “Modelling of CO2 content in the atmosphere until 2300: Influence of energy intensity of gross domestic product and carbon intensity of energy”, International Journal of Global Warming, pp. 1-17, 2013.
[9] CJ Butcher, BV Reddy: “Second law analysis of a waste heat recovery based power generation system”, International Journal of Heat and Mass Transfer, pp. 2355—2363, 2007.
[10] R. Chacartegui, B. Monje, D. Sánchez, J.A. Becerra, S. Campanari: “Molten carbonate fuel cell: Towards negative emissions in wastewater treatment CHP plants”, International Journal of Greenhouse Gas Control, pp. 453-461, 2013.
[11] R. Chacartegui, B. Monje, D. Sánchez, J.A. Becerra, S. Campanari: “Molten carbonate fuel cell: Towards negative emissions in wastewater treatment CHP plants”, International Journal of Greenhouse Gas Control, pp. 453-461, 2013.
[12] Georges Descombes, Serge Boudigues: “Modelling of waste heat recovery for combined heat and power applications”, Applied Thermal Engineering, pp. 2610—2616, 2009.
[13] J. Ding, X. Li, J. Cao, L. Sheng, L. Yin, X. Xu: “New sensor for gases dissolved in transformer oil based on solid oxide fuel cell”, Sensors and Actuators, B: Chemical, pp. 232-239, 2014.
[14] J. Ding, X. Li, J. Cao, L. Sheng, L. Yin, X. Xu: “New sensor for gases dissolved in transformer oil based on solid oxide fuel cell”, Sensors and Actuators, B: Chemical, pp. 232-239, 2014.
[15] D. Grondin, J. Deseure, P. Ozil, J.-P. Chabriat, B. Grondin-Perez, A. Brisse: “Solid oxide electrolysis cell 3D simulation using artificial neural network for cathodic process description”, Chemical Engineering Research and Design, pp. 134-140, 2013.
[16] D. Grondin, J. Deseure, P. Ozil, J.-P. Chabriat, B. Grondin-Perez, A. Brisse: “Solid oxide electrolysis cell 3D simulation using artificial neural network for cathodic process description”, Chemical Engineering Research and Design, pp. 134-140, 2013.
[17] C. Guerra, A. Lanzini, P. Leone, M. Santarelli, D. Beretta: “Experimental study of dry reforming of biogas in a tubular anode-supported solid oxide fuel cell”, International Journal of Hydrogen Energy, pp. 10559-10566, 2013.
[18] C. Guerra, A. Lanzini, P. Leone, M. Santarelli, D. Beretta: “Experimental study of dry reforming of biogas in a tubular anode-supported solid oxide fuel cell”, International Journal of Hydrogen Energy, pp. 10559-10566, 2013.
[19] S.A. Hajimolana, S.M. Tonekabonimoghadam, M.A. Hussain, M.H. Chakrabarti, N.S. Jayakumar, M.A. Hashim: “Thermal stress management of a solid oxide fuel cell using neural network predictive control”, Energy, pp. 320-329, 2013.
[20] S.A. Hajimolana, S.M. Tonekabonimoghadam, M.A. Hussain, M.H. Chakrabarti, N.S. Jayakumar, M.A. Hashim: “Thermal stress management of a solid oxide fuel cell using neural network predictive control”, Energy, pp. 320-329, 2013.
[21] E. Hosseinzadeh, M. Rokni, M. Jabbari, H. Mortensen: “Numerical analysis of transport phenomena for designing of ejector in PEM forklift system”, International Journal of Hydrogen Energy, pp. 6664-6674, 2014.
[22] E. Hosseinzadeh, M. Rokni, M. Jabbari, H. Mortensen: “Numerical analysis of transport phenomena for designing of ejector in PEM forklift system”, International Journal of Hydrogen Energy, pp. 6664-6674, 2014.
[23] J. Chawla: “Waste heat recovery from flue gases with substantial dust load”, Chemical Engineering and Processing, pp. 365—371, 1999.
[24] Jan Pawel Stempien, Qiang Sun, Siew Hwa Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions ”, Energy , pp. 647 - 657, 2013. URL http://www.sciencedirect.com/science/article/pii/S0360544213002193.
[25] E. Jannelli, M. Minutillo, A. Perna: “Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances”, Applied Energy, pp. 82-91, 2013.
[26] E. Jannelli, M. Minutillo, A. Perna: “Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances”, Applied Energy, pp. 82-91, 2013.
[27] Jarosław Milewski, Krzysztof Badyda, Zbigniew Misztal, Marcin Wołowicz: “Combined Heat and Power Unit Based on Polymeric Electrolyte Membrane Fuel Cell in A Hotel Application”, Rynek Energii, pp. 118—123, 2010. Indexed by Journal Citation Reports with Impact Factor of 0.63, Cited 1 time.
[28] Janusz Kotowicz, Łukasz Bartela: “The influence of economic parameters on the optimal values of the design variables of a combined cycle plant”, Energy, pp. 911—919, 2010.
[29] Janusz Kotowicz, Łukasz Bartela: “The influence of economic parameters on the optimal values of the design variables of a combined cycle plant”, Energy, pp. 911—919, 2010.
[30] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[31] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[32] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[33] J. Kupecki, J. Jewulski, K. Motylinski: “SOFC (solid oxide fuel cell) μ-CHP (combined heat and power) system with oxy-combustion based on oxygen separation membranes”, Proceedings of the 26th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems, ECOS 2013, 2013.
[34] Sau Man Lai, Hao Wu, Chi Wai Hui, Ben Hua, Gaobo Zhang: “Flexible heat exchanger network design for low-temperature heat utilization in oil refinery”, Asia-Pacific Journal of Chemical Engineering, pp. 713—733, 2011.
[35] D. Marra, M. Sorrentino, C. Pianese, B. Iwanschitz: “A neural network estimator of Solid Oxide Fuel Cell performance for on-field diagnostics and prognostics applications”, Journal of Power Sources, pp. 320-329, 2013.
[36] D. Marra, M. Sorrentino, C. Pianese, B. Iwanschitz: “A neural network estimator of Solid Oxide Fuel Cell performance for on-field diagnostics and prognostics applications”, Journal of Power Sources, pp. 320-329, 2013.
[37] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[38] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[39] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[40] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[41] Lan Peng, You-Rong Li, Shuang-Ying Wu, Bo Lan: “The analysis of exergy efficiency in the low temperature heat exchanger”, International Journal of Modern Physics B, pp. 3497—3499, 2007.
[42] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[43] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[44] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[45] M.Y. Ramandi, I. Dincer, P. Berg: “A transient analysis of three-dimensional heat and mass transfer in a molten carbonate fuel cell at start-up”, International Journal of Hydrogen Energy, pp. 8034-8047, 2014.
[46] M.Y. Ramandi, I. Dincer, P. Berg: “A transient analysis of three-dimensional heat and mass transfer in a molten carbonate fuel cell at start-up”, International Journal of Hydrogen Energy, pp. 8034-8047, 2014.
[47] O. Razbani, M. Assadi: “Artificial neural network model of a short stack solid oxide fuel cell based on experimental data”, Journal of Power Sources, pp. 581-586, 2014.
[48] O. Razbani, M. Assadi: “Artificial neural network model of a short stack solid oxide fuel cell based on experimental data”, Journal of Power Sources, pp. 581-586, 2014.
[49] J-Y San: “Second-law performance of heat exchangers for waste heat recovery”, Energy, pp. 1936—1945, 2010.
[50] D. Sanchez, B. Monje, R. Chacartegui, S. Campanari: “Potential of molten carbonate fuel cells to enhance the performance of CHP plants in sewage treatment facilities”, International Journal of Hydrogen Energy, pp. 394-405, 2013.
[51] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[52] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[53] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[54] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[55] Fredrik Starfelt, Eva Thorin, Erik Dotzauer, Jinyue Yan: “Performance evaluation of adding ethanol production into an existing combined heat and power plant”, Bioresource technology, pp. 613—618, 2010.
[56] J.P. Stempien, Q. Sun, S.H. Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions”, Energy, pp. 647-657, 2013.
[57] J.P. Stempien, Q. Sun, S.H. Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions”, Energy, pp. 647-657, 2013.
[58] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[59] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[60] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[61] W. Wang, H. Li, X.-F. Wang: “Analyses of part-load control modes and their performance of a SOFC/MGT hybrid power system”, Dalian Ligong Daxue Xuebao/Journal of Dalian University of Technology, pp. 653-658, 2013.
[62] W. Wang, H. Li, X.-F. Wang: “Analyses of part-load control modes and their performance of a SOFC/MGT hybrid power system”, Dalian Ligong Daxue Xuebao/Journal of Dalian University of Technology, pp. 653-658, 2013.
[63] J.-H. Wee: “Carbon dioxide emission reduction using molten carbonate fuel cell systems”, Renewable and Sustainable Energy Reviews, pp. 178-191, 2014.
[64] J.-H. Wee: “Carbon dioxide emission reduction using molten carbonate fuel cell systems”, Renewable and Sustainable Energy Reviews, pp. 178-191, 2014.
[65] SY Wu, YR Li, DL Zeng: “Exergo-economic performance evaluation on low temperature heat exchanger”, International Journal of Modern Physics B, pp. 517—519, 2005.
[66] SY Wu, YR Li, DL Zeng: “Exergo-economic performance evaluation on low temperature heat exchanger”, International Journal of Modern Physics B, pp. 517—519, 2005.
[67] SY Wu, XF Yuan, YR Li, L Peng: “Exergy transfer characteristics on low temperature heat exchangers”, International Journal of Modern Physics B, pp. 3503—3505, 2007.
[68] H. Xu, Z. Dang, B.-F. Bai: “Electrochemical performance study of solid oxide fuel cell using lattice Boltzmann method”, Energy, pp. 575-583, 2014.
[69] H. Xu, Z. Dang, B.-F. Bai: “Electrochemical performance study of solid oxide fuel cell using lattice Boltzmann method”, Energy, pp. 575-583, 2014.
[70] A. Zamaniyan, F. Joda, A. Behroozsarand, H. Ebrahimi: “Application of artificial neural networks (ANN) for modeling of industrial hydrogen plant”, International Journal of Hydrogen Energy, pp. 6289-6297, 2013.
[71] A. Zamaniyan, F. Joda, A. Behroozsarand, H. Ebrahimi: “Application of artificial neural networks (ANN) for modeling of industrial hydrogen plant”, International Journal of Hydrogen Energy, pp. 6289-6297, 2013.
[2] M. Amirinejad, N. Tavajohi-Hasankiadeh, S.S. Madaeni, M.A. Navarra, E. Rafiee, B. Scrosati: “Adaptive neuro-fuzzy inference system and artificial neural network modeling of proton exchange membrane fuel cells based on nanocomposite and recast Nafion membranes”, International Journal of Energy Research, pp. 347-357, 2013.
[3] D.P. Bakalis, A.G. Stamatis: “Incorporating available micro gas turbines and fuel cell: Matching considerations and performance evaluation”, Applied Energy, pp. 607-617, 2013.
[4] D.P. Bakalis, A.G. Stamatis: “Incorporating available micro gas turbines and fuel cell: Matching considerations and performance evaluation”, Applied Energy, pp. 607-617, 2013.
[5] T. Bartela, A. Skorek-Osikowska, J. Kotowicz: “Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation”, Energy, pp. 513-523, 2014.
[6] T. Bartela, A. Skorek-Osikowska, J. Kotowicz: “Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation”, Energy, pp. 513-523, 2014.
[7] W.M. Budzianowski: “Modelling of CO2 content in the atmosphere until 2300: Influence of energy intensity of gross domestic product and carbon intensity of energy”, International Journal of Global Warming, pp. 1-17, 2013.
[8] W.M. Budzianowski: “Modelling of CO2 content in the atmosphere until 2300: Influence of energy intensity of gross domestic product and carbon intensity of energy”, International Journal of Global Warming, pp. 1-17, 2013.
[9] CJ Butcher, BV Reddy: “Second law analysis of a waste heat recovery based power generation system”, International Journal of Heat and Mass Transfer, pp. 2355—2363, 2007.
[10] R. Chacartegui, B. Monje, D. Sánchez, J.A. Becerra, S. Campanari: “Molten carbonate fuel cell: Towards negative emissions in wastewater treatment CHP plants”, International Journal of Greenhouse Gas Control, pp. 453-461, 2013.
[11] R. Chacartegui, B. Monje, D. Sánchez, J.A. Becerra, S. Campanari: “Molten carbonate fuel cell: Towards negative emissions in wastewater treatment CHP plants”, International Journal of Greenhouse Gas Control, pp. 453-461, 2013.
[12] Georges Descombes, Serge Boudigues: “Modelling of waste heat recovery for combined heat and power applications”, Applied Thermal Engineering, pp. 2610—2616, 2009.
[13] J. Ding, X. Li, J. Cao, L. Sheng, L. Yin, X. Xu: “New sensor for gases dissolved in transformer oil based on solid oxide fuel cell”, Sensors and Actuators, B: Chemical, pp. 232-239, 2014.
[14] J. Ding, X. Li, J. Cao, L. Sheng, L. Yin, X. Xu: “New sensor for gases dissolved in transformer oil based on solid oxide fuel cell”, Sensors and Actuators, B: Chemical, pp. 232-239, 2014.
[15] D. Grondin, J. Deseure, P. Ozil, J.-P. Chabriat, B. Grondin-Perez, A. Brisse: “Solid oxide electrolysis cell 3D simulation using artificial neural network for cathodic process description”, Chemical Engineering Research and Design, pp. 134-140, 2013.
[16] D. Grondin, J. Deseure, P. Ozil, J.-P. Chabriat, B. Grondin-Perez, A. Brisse: “Solid oxide electrolysis cell 3D simulation using artificial neural network for cathodic process description”, Chemical Engineering Research and Design, pp. 134-140, 2013.
[17] C. Guerra, A. Lanzini, P. Leone, M. Santarelli, D. Beretta: “Experimental study of dry reforming of biogas in a tubular anode-supported solid oxide fuel cell”, International Journal of Hydrogen Energy, pp. 10559-10566, 2013.
[18] C. Guerra, A. Lanzini, P. Leone, M. Santarelli, D. Beretta: “Experimental study of dry reforming of biogas in a tubular anode-supported solid oxide fuel cell”, International Journal of Hydrogen Energy, pp. 10559-10566, 2013.
[19] S.A. Hajimolana, S.M. Tonekabonimoghadam, M.A. Hussain, M.H. Chakrabarti, N.S. Jayakumar, M.A. Hashim: “Thermal stress management of a solid oxide fuel cell using neural network predictive control”, Energy, pp. 320-329, 2013.
[20] S.A. Hajimolana, S.M. Tonekabonimoghadam, M.A. Hussain, M.H. Chakrabarti, N.S. Jayakumar, M.A. Hashim: “Thermal stress management of a solid oxide fuel cell using neural network predictive control”, Energy, pp. 320-329, 2013.
[21] E. Hosseinzadeh, M. Rokni, M. Jabbari, H. Mortensen: “Numerical analysis of transport phenomena for designing of ejector in PEM forklift system”, International Journal of Hydrogen Energy, pp. 6664-6674, 2014.
[22] E. Hosseinzadeh, M. Rokni, M. Jabbari, H. Mortensen: “Numerical analysis of transport phenomena for designing of ejector in PEM forklift system”, International Journal of Hydrogen Energy, pp. 6664-6674, 2014.
[23] J. Chawla: “Waste heat recovery from flue gases with substantial dust load”, Chemical Engineering and Processing, pp. 365—371, 1999.
[24] Jan Pawel Stempien, Qiang Sun, Siew Hwa Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions ”, Energy , pp. 647 - 657, 2013. URL http://www.sciencedirect.com/science/article/pii/S0360544213002193.
[25] E. Jannelli, M. Minutillo, A. Perna: “Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances”, Applied Energy, pp. 82-91, 2013.
[26] E. Jannelli, M. Minutillo, A. Perna: “Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances”, Applied Energy, pp. 82-91, 2013.
[27] Jarosław Milewski, Krzysztof Badyda, Zbigniew Misztal, Marcin Wołowicz: “Combined Heat and Power Unit Based on Polymeric Electrolyte Membrane Fuel Cell in A Hotel Application”, Rynek Energii, pp. 118—123, 2010. Indexed by Journal Citation Reports with Impact Factor of 0.63, Cited 1 time.
[28] Janusz Kotowicz, Łukasz Bartela: “The influence of economic parameters on the optimal values of the design variables of a combined cycle plant”, Energy, pp. 911—919, 2010.
[29] Janusz Kotowicz, Łukasz Bartela: “The influence of economic parameters on the optimal values of the design variables of a combined cycle plant”, Energy, pp. 911—919, 2010.
[30] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[31] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[32] Krzysztof Badyda, Jarosław Milewski, Marcin Wołowicz: “Model of 800~MW condensation power plant unit using GateCycletm aplication”, , 2011.
[33] J. Kupecki, J. Jewulski, K. Motylinski: “SOFC (solid oxide fuel cell) μ-CHP (combined heat and power) system with oxy-combustion based on oxygen separation membranes”, Proceedings of the 26th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems, ECOS 2013, 2013.
[34] Sau Man Lai, Hao Wu, Chi Wai Hui, Ben Hua, Gaobo Zhang: “Flexible heat exchanger network design for low-temperature heat utilization in oil refinery”, Asia-Pacific Journal of Chemical Engineering, pp. 713—733, 2011.
[35] D. Marra, M. Sorrentino, C. Pianese, B. Iwanschitz: “A neural network estimator of Solid Oxide Fuel Cell performance for on-field diagnostics and prognostics applications”, Journal of Power Sources, pp. 320-329, 2013.
[36] D. Marra, M. Sorrentino, C. Pianese, B. Iwanschitz: “A neural network estimator of Solid Oxide Fuel Cell performance for on-field diagnostics and prognostics applications”, Journal of Power Sources, pp. 320-329, 2013.
[37] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[38] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[39] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[40] D. McLarty, J. Brouwer, S. Samuelsen: “Hybrid fuel cell gas turbine system design and optimization”, Journal of Fuel Cell Science and Technology, 2013.
[41] Lan Peng, You-Rong Li, Shuang-Ying Wu, Bo Lan: “The analysis of exergy efficiency in the low temperature heat exchanger”, International Journal of Modern Physics B, pp. 3497—3499, 2007.
[42] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[43] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[44] J. Qian, Z. Tao, J. Xiao, G. Jiang, W. Liu: “Performance improvement of ceria-based solid oxide fuel cells with yttria-stabilized zirconia as an electronic blocking layer by pulsed laser deposition”, International Journal of Hydrogen Energy, pp. 2407-2412, 2013.
[45] M.Y. Ramandi, I. Dincer, P. Berg: “A transient analysis of three-dimensional heat and mass transfer in a molten carbonate fuel cell at start-up”, International Journal of Hydrogen Energy, pp. 8034-8047, 2014.
[46] M.Y. Ramandi, I. Dincer, P. Berg: “A transient analysis of three-dimensional heat and mass transfer in a molten carbonate fuel cell at start-up”, International Journal of Hydrogen Energy, pp. 8034-8047, 2014.
[47] O. Razbani, M. Assadi: “Artificial neural network model of a short stack solid oxide fuel cell based on experimental data”, Journal of Power Sources, pp. 581-586, 2014.
[48] O. Razbani, M. Assadi: “Artificial neural network model of a short stack solid oxide fuel cell based on experimental data”, Journal of Power Sources, pp. 581-586, 2014.
[49] J-Y San: “Second-law performance of heat exchangers for waste heat recovery”, Energy, pp. 1936—1945, 2010.
[50] D. Sanchez, B. Monje, R. Chacartegui, S. Campanari: “Potential of molten carbonate fuel cells to enhance the performance of CHP plants in sewage treatment facilities”, International Journal of Hydrogen Energy, pp. 394-405, 2013.
[51] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[52] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[53] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[54] S. Sieniutycz, J. Jezowski: Energy Optimization in Process Systems and Fuel Cells. 2013.
[55] Fredrik Starfelt, Eva Thorin, Erik Dotzauer, Jinyue Yan: “Performance evaluation of adding ethanol production into an existing combined heat and power plant”, Bioresource technology, pp. 613—618, 2010.
[56] J.P. Stempien, Q. Sun, S.H. Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions”, Energy, pp. 647-657, 2013.
[57] J.P. Stempien, Q. Sun, S.H. Chan: “Performance of power generation extension system based on solid-oxide electrolyzer cells under various design conditions”, Energy, pp. 647-657, 2013.
[58] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[59] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[60] S.-B. Wang, C.-F. Wu, S.-F. Liu, P. Yuan: “Performance optimization and selection of operating parameters for a solid oxide fuel cell stack”, Journal of Fuel Cell Science and Technology, 2013.
[61] W. Wang, H. Li, X.-F. Wang: “Analyses of part-load control modes and their performance of a SOFC/MGT hybrid power system”, Dalian Ligong Daxue Xuebao/Journal of Dalian University of Technology, pp. 653-658, 2013.
[62] W. Wang, H. Li, X.-F. Wang: “Analyses of part-load control modes and their performance of a SOFC/MGT hybrid power system”, Dalian Ligong Daxue Xuebao/Journal of Dalian University of Technology, pp. 653-658, 2013.
[63] J.-H. Wee: “Carbon dioxide emission reduction using molten carbonate fuel cell systems”, Renewable and Sustainable Energy Reviews, pp. 178-191, 2014.
[64] J.-H. Wee: “Carbon dioxide emission reduction using molten carbonate fuel cell systems”, Renewable and Sustainable Energy Reviews, pp. 178-191, 2014.
[65] SY Wu, YR Li, DL Zeng: “Exergo-economic performance evaluation on low temperature heat exchanger”, International Journal of Modern Physics B, pp. 517—519, 2005.
[66] SY Wu, YR Li, DL Zeng: “Exergo-economic performance evaluation on low temperature heat exchanger”, International Journal of Modern Physics B, pp. 517—519, 2005.
[67] SY Wu, XF Yuan, YR Li, L Peng: “Exergy transfer characteristics on low temperature heat exchangers”, International Journal of Modern Physics B, pp. 3503—3505, 2007.
[68] H. Xu, Z. Dang, B.-F. Bai: “Electrochemical performance study of solid oxide fuel cell using lattice Boltzmann method”, Energy, pp. 575-583, 2014.
[69] H. Xu, Z. Dang, B.-F. Bai: “Electrochemical performance study of solid oxide fuel cell using lattice Boltzmann method”, Energy, pp. 575-583, 2014.
[70] A. Zamaniyan, F. Joda, A. Behroozsarand, H. Ebrahimi: “Application of artificial neural networks (ANN) for modeling of industrial hydrogen plant”, International Journal of Hydrogen Energy, pp. 6289-6297, 2013.
[71] A. Zamaniyan, F. Joda, A. Behroozsarand, H. Ebrahimi: “Application of artificial neural networks (ANN) for modeling of industrial hydrogen plant”, International Journal of Hydrogen Energy, pp. 6289-6297, 2013.
Published
2015-10-03
How to Cite
MILEWSKI, Jaroslaw et al.
Off-design operation of an 900 MW-class power plant with utilization of low temperature heat of flue gases.
Journal of Power Technologies, [S.l.], v. 95, n. 3, p. 221--227, oct. 2015.
ISSN 2083-4195.
Available at: <https://papers.itc.pw.edu.pl/index.php/JPT/article/view/617>. Date accessed: 26 apr. 2024.
Issue
Section
Power Plant
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
